RUT300

Overview

The RUT300 is a small, but powerful Ethernet router perfect for challenging industrial networking tasks as well as general networking applications. Five Ethernet ports, two configurable digital Inputs/Outputs, and a USB port to easily connect the various equipment to the internet. Preconfigured Firewall for immediate security and multiple top-rated VPNs. Passive PoE helps to reduce deployment complexity. Economical but a feature-rich industrial device that comes with all the benefits of RutOS and Remote Management System (RMS).

Features

Ethernet
WAN
1 x WAN port (can be configured as LAN) 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover
LAN
4 x LAN ports (can be configured as secondary WAN ports), 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover
Network
Routing
Static routes, Dynamic routes (planned)
Network protocols
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP (planned), SMTP, SSL v3, TLS, ARP, PPPoE, UPNP, SSH, DHCP, Telnet client, SNMP (planned), MQTT (planned), Wake on LAN (WOL) (planned)
VoIP passthrough support
H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
Connection monitoring
Ping Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection
Firewall
Port forwards, traffic rules, custom rules
DHCP
Static and dynamic IP allocation, DHCP Relay, Relayd
QoS / Smart Queue Management (SQM) (planned)
Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
DDNS (planned) Supported >25 service providers, others can be configured manually
Network backup
Wired WAN options, each of which can be used as an automatic Failover
Load balancing
Balance Internet traffic over multiple WAN connections
SSHFS
Possibility to mount remote file system via SSH protocol
Security

Authentication
Pre-shared key, digital certificates, X.509 certificates
Firewall
Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
Attack prevention
DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)
VLAN
Port and tag based VLAN separation
WEB filter (planned)
Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only
Access control
Flexible access control of TCP, UDP, ICMP packets, MAC address filter
VPN

OpenVPN
Multiple clients and a server can run simultaneously, 12 encryption methods
OpenVPN Encryption
DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC
IPSec
IKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256)
GRE
GRE tunnel
PPTP, L2TP
Client/Server instances can run simultaneously, L2TPv3 support (planned)
Stunnel (planned)
Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code
DMVPN (planned)
Method of building scalable IPsec VPNs
SSTP (planned)
SSTP client instance support
ZeroTier
ZeroTier VPN client support
WireGuard
WireGuard VPN client and server support
Modbus

Modbus TCP Slave (planned)

ID filtering
Respond to one ID in range [1;255] or any
Allow remote access
Allow access through WAN
Custom registers
MODBUS TCP custom register block, which allows to read/write to a file inside the router, and can be used to extend MODBUS TCP slave functionality
Modbus TCP Master (planned)

Supported functions
01, 02, 03, 04, 05, 06, 15, 16
Supported data formats
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII
MQTT Gateway (planned)

Gateway
Allows sending commands and receiving data from MODBUS Master trough MQTT broker
Data to Server (planned)

Protocols
HTTP(S), MQTT, Azure MQTT, Kinesis
Monitoring & Management

WEB UI
HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log
FOTA
Firmware update from server, automatic notification
SSH
SSH (v1, v2)
TR-069
OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
MQTT
MQTT Broker, MQTT publisher
SNMP
SNMP (v1, v2, v3), SNMP trap
JSON-RPC
Management API over HTTP/HTTPS
MODBUS (planned)
MODBUS TCP status/control
RMS
Teltonika Remote Management System (RMS)
System Characteristics

CPU
QCA9531, MIPS 24kc, 650 MHz
RAM
64 MB, DDR2
FLASH storage
16 MB, SPI Flash
Firmware / Configuration

WEB UI
Update FW from file, check FW on server, configuration profiles, configuration backup
FOTA
Update FW/configuration from server
RMS
Update FW/configuration for multiple devices at once
Keep settings
Update FW without losing current configuration
Firmware Customization

Operating system
RutOS (OpenWrt based Linux OS)
Supported languages
Busybox shell, Lua, C, C++
Development tools
SDK package with build environment provided
USB

Data rate
USB 2.0
Applications
Samba share, USB-to-serial
External devices
Possibility to connect external HDD, flash drive, additional modem, printer
Storage formats
FAT, FAT32, NTFS
Input/Output
Configurable I/O
2 x Configurable digital Inputs/Outputs. Digital input 0 - 6 V detected as logic low, 8 - 30 V detected as logic high. Open collector output, max output 30 V, 300 mA
Events
Email, RMS
I/O juggler
Allows to set certain I/O conditions to initiate event
Power

Connector
4 pin industrial DC power socket
Input voltage range
7 - 30 VDC, reverse polarity protection, voltage surge/transient protection
PoE (passive)
Passive PoE. Possibility to power up through LAN port, not compatible with IEEE 802.3af, 802.3at and 802.3bt standards
Power consumption
Idle: 1.3 W, Max: 3 W
Physical Interfaces (Ports, Led's, Buttons)
Ethernet
5 x RJ45 ports, 10/100 Mbps
I/Os
2 x Configurable digital Inputs/Outputs on 4 pin power connector
Status LEDs
5 x ETH status, 1 x Power
Power
1 x 4 pin DC connector
USB
1 x USB A port for external devices
Reset
Reboot/User default reset/Factory reset button
Physical Specifications

Casing material
Aluminium housing with DIN rail mounting option
Dimensions (W x H x D)
100 x 30 x 85 mm
Weight
229 g
Mounting options
DIN rail, flat surface placement
Operating Environment
Operating temperature
-40 C to 75 C
Operating humidity
10 % to 90 % non-condensing

Resources